Key Takeaways
- What it does: An SDI to IPTV encoder takes an uncompressed SDI video signal from a camera, switcher or router and turns it into a compressed IP stream for TVs, apps and servers.
- SDI is uncompressed: A 3G-SDI link carries about 2.97 Gbit/s. The encoder compresses it to a few Mbit/s so it fits on a normal network.
- Match the SDI speed: SD, HD and 3G-SDI inputs cover most 1080p work. 4K sources need 6G-SDI or 12G-SDI inputs, which are less common on IPTV encoders.
- Check multicast and protocols: Hotels and campuses need UDP or RTP multicast with IGMP. Internet delivery needs HLS, RTMP or SRT.
- Plan the network: Total bitrate must fit your switches and the encoder’s port. A dual-stream encoder doubles the load.
- SDI is a professional signal: It is usually unencrypted, so it is used inside studios and facilities. You still need the right to redistribute the content.
- We did not test these units: The examples below come from vendor pages, so verify specs and prices before buying.
An SDI to IPTV encoder is the bridge between broadcast video gear and an IP network. It is common in hotels, studios, venues, churches and small TV operators that already have SDI cameras, switchers or routers. This guide explains how it works, what to compare and how to set one up.
It is written for IT staff, integrators and new IPTV operators. Product examples show categories, not rankings, and every detail comes from vendor pages. We did not run hands-on tests.
What Is an SDI to IPTV Encoder?
An SDI to IPTV encoder is a hardware device with an SDI input and a network output. The Serial Digital Interface (SDI) is a family of professional video connections first standardized by SMPTE in 1989. The encoder compresses the SDI signal into H.264 or HEVC and sends it as an IP stream.
Other devices on the network then play that stream like any other IPTV channel. The encoder is one part of a larger system. Our guide to the IPTV headend shows where encoders fit, and our explainer on IPTV encoders covers the main types.
SDI vs HDMI: Why Use SDI?
| Feature | SDI | HDMI |
|---|---|---|
| Typical use | Cameras, switchers and routers in studios | Consumer and office devices |
| Cable | 75 ohm coaxial cable with BNC connectors | HDMI cable |
| Reach | Longer runs, though distance falls as the speed rises | Shorter runs without extenders |
| Audio | Usually embedded in the SDI signal | Embedded in the HDMI signal |
| Equipment cost | Higher, because it is professional gear | Lower |
SDI also carries embedded audio, so one cable can hold video and sound together. The distance you can reach depends on the SDI speed and cable quality. The Broadcast Bridge notes that the reliable distance shrinks as bandwidth rises, and that it could be under 100 meters for 12G-SDI.
SDI Formats at a Glance
The SDI family has grown with video resolution. The table shows the main versions, based on the SDI standards.
| Format | Standard | Data rate | Typical video |
|---|---|---|---|
| SD-SDI | SMPTE 259M | Up to 270 Mbit/s | 480i and 576i |
| HD-SDI | SMPTE 292M | 1.485 Gbit/s | 720p and 1080i |
| 3G-SDI | SMPTE 424M | 2.970 Gbit/s | 1080p60 |
| 6G-SDI | SMPTE ST 2081 | 6 Gbit/s | 2160p30 |
| 12G-SDI | SMPTE ST 2082 | 12 Gbit/s | 2160p60 |
Most IPTV encoders accept SD, HD and 3G-SDI and output up to 1080p60. Always check that the encoder matches the speed your source sends. A 4K camera on 12G-SDI needs a 6G or 12G input.
How an SDI to IPTV Encoder Works
The encoder receives the uncompressed SDI signal and extracts the embedded audio. It compresses the picture and sound, packages them for the network and sends them out over Ethernet. This drops the data from about 3 Gbit/s to a few Mbit/s, which a normal network can carry.
Most units can send more than one stream from the same input, for example a high-quality stream for TVs and a lighter one for phones. This is the same idea behind adaptive bitrate streaming, where several quality levels let the player choose the best fit. For on-demand video, see our guide to VOD, which does not need a live encoder.
What to Look For in an SDI IPTV Encoder
| Feature | Why it matters | What to check |
|---|---|---|
| SDI input type | Must match your source | SD, HD or 3G-SDI, and 6G or 12G for 4K |
| Channels per unit | Sets cost, space and rack design | One channel, four channels or a multi-card chassis |
| Codec | Decides quality per megabit | H.264 for wide compatibility, HEVC for lower bitrate |
| Output resolution and frame rate | Input and output can differ | For example 1080p60 |
| Output protocols | Must match your network and TVs | UDP or RTP multicast, HLS, RTSP, RTMP, SRT |
| Multicast and IGMP | Needed to share one stream with many TVs | IGMP v2 or v3 support |
| Latency | Matters for live events | Vendor figures, and test your own setup |
| Loop-through | Lets you feed another device | An SDI loop-out or loop-through |
| Audio | TVs and middleware are picky | Embedded audio, AAC, MP2 or AC3 |
| Network port | Limits total bitrate | Gigabit if you run several streams |
| Build | Headends run all day | Fanless or rack design, warranty and 24/7 rating |
H.264 or HEVC
H.264 plays almost everywhere, so it is the safe choice for hotel TVs and older devices. HEVC (H.265) delivers similar quality at a lower bitrate. Vendor claims about the saving vary widely, from about 30% on one product page to up to four times on another, so test with your own content.
SPTS or MPTS
A single program transport stream (SPTS) carries one channel, and a multi-program transport stream (MPTS) bundles several. Hotel middleware often expects one multicast address per channel, so check what your system requires.
Examples of SDI to IPTV Encoders by Category
The table lists example units from different categories. They are not ranked or tested, and the details come from vendor pages. Confirm the current specs and price with each vendor.
| Example | SDI inputs | Maximum video | Codecs | Multicast | Notes from the vendor |
|---|---|---|---|---|---|
| ProVideo Instruments VeCASTER HD SDI HEVC | 1 x 3G-HD-SDI | 1080p60 | H.265 and H.264 | UDP/RTP, IGMP v1 to v3 | Two independent streams, SRT, HLS, fanless case, 5-year warranty |
| Blankom SDE-265 | 1 x HD-SDI or SD-SDI, with loop-through | 1080p60 | H.265, H.264, MJPEG | UDP/RTP | Two streams, SRT, video rate 0.1 to 32 Mbps |
| TBS2602V2 | 1 x SD, HD or 3G-SDI | 1080p60 | H.264 and H.265 | RTP/UDP | SDI loop-out, SRT caller and listener, 24/7 operation, up to 4 stereo audio tracks |
| Fiberlink-AV 4-channel IPTV H.265 SDI encoder | 4 x HD or 3G-SDI | 1080p60 | H.265 and H.264 | UDP | Gigabit port, vendor mentions hotel IPTV use |
| ProVideo Instruments INFINIUM 3G-SDI HEVC card | 1 x 3G-SDI per card | 1080p | HEVC, H.264, MJPEG | UDP/RTP, IGMP v1 to v3 | Hot-swappable card for a multi-slot chassis, four simultaneous streams |
Two lessons stand out. First, most SDI encoders top out at 1080p60, even when the SDI input supports faster formats. Second, some vendors also build multi-channel units that take both SDI and HDMI inputs, so you can mix sources in one rack. Always read the spec sheet line by line.
Which Type Should You Choose?
- One or two cameras or switcher outputs: A single-channel encoder with SRT or RTMP.
- Hotel or campus with several channels: A multi-channel unit or chassis with UDP or RTP multicast and Gigabit.
- Live events with low delay: Look for SRT, and test latency on your own network.
- Mixed SDI and HDMI sources: A multi-channel unit that accepts both, or two separate units.
- 4K sources: Check the SDI speed and the encoder’s output size before you pay for 4K.
Plan Your Bandwidth
Multiply the number of channels by the bitrate of each stream. These bitrates are examples only, so use your own settings. A dual-stream encoder sends two streams per input, so double the total if you run both.
| Channels | Bitrate per channel | Total outbound |
|---|---|---|
| 4 | 5 Mbps | 20 Mbps |
| 8 | 6 Mbps | 48 Mbps |
| 16 | 8 Mbps | 128 Mbps |
A 100 Mbps port cannot carry the last row, and it leaves little headroom on the 8-channel one. Choose Gigabit for larger sets. For how multicast and unicast load a network, see our IPTV headend guide and the overview of IP multicast.
How to Set Up an SDI to IPTV Encoder
- Confirm the license. Make sure you have the right to redistribute the source.
- Connect the SDI source. Use a 75 ohm coaxial cable with BNC connectors. Network cables use different connectors, so do not mix them up.
- Connect the network. Plug the encoder into a Gigabit switch port.
- Open the web interface. Most units are configured through a browser.
- Set the video. Choose the codec, resolution, frame rate and bitrate.
- Set the audio. Choose embedded SDI audio or an external input, and pick a format your TVs support.
- Choose the output. For a managed network, pick a multicast address and port for each channel. For internet delivery, choose SRT, RTMP or HLS.
- Configure the network. Set up IGMP and, if possible, a separate VLAN for IPTV.
- Test the stream. Open the network address in a player such as VLC to check picture and sound.
- Add it to your system. Add the channel to your middleware or IPTV player, and monitor it for dropped packets.
SDI Licensing and Protection
SDI carries uncompressed, unencrypted video, and that is why it is mostly found in professional equipment. Wikipedia notes that licensing agreements restrict the use of unencrypted interfaces like SDI in consumer devices. In a studio or facility, you control the source, so this is rarely a problem.
Streaming a signal over IP is a different matter. You need the right to show each channel to your audience, whether that is hotel rooms or paying subscribers. Redistributing channels without rights is copyright infringement, whatever equipment you use. If you plan to sell TV service, read our guide to starting an IPTV business and our overview of legal IPTV services.
Common Mistakes When Buying an SDI Encoder
- Ignoring SDI speed: A 3G-only input will not accept a 6G or 12G signal.
- Expecting 4K output: Many units accept faster SDI but encode to 1080p60.
- Skipping multicast support: Without it, one stream per viewer can overload a small network.
- Underestimating bitrate: Several channels, or dual streams, fill a 100 Mbps port fast.
- Mixing up connectors: SDI uses 75 ohm BNC, and network cabling does not.
- No monitoring: Without alarms, you learn about failures from complaints.
SDI to IPTV Encoder Checklist
- List each SDI source and its format.
- Confirm that you have the license for each channel.
- Pick H.264 or HEVC based on your TVs.
- Confirm output resolution, frame rate and multicast support.
- Calculate total bitrate, including second streams, and choose a Gigabit port if needed.
- Plan IGMP, a VLAN and a way to monitor streams.
- Test with real TVs and real receivers before you launch.
To see where this technology is heading, read about the future of IPTV and how it differs from satellite TV.
SDI to IPTV Encoder FAQ
-
What is an SDI to IPTV encoder?
It is a device that compresses an SDI video signal and sends it as an IP stream. Other devices on the network can then play the stream as an IPTV channel.
-
What is the difference between SDI and HDMI encoders?
The encoding is similar, but the input differs. SDI encoders use BNC coaxial inputs found on professional gear, while HDMI encoders use consumer HDMI inputs.
-
Can I use an SDI to HDMI converter with an HDMI encoder?
Yes, but it adds another device and another point of failure. A native SDI encoder is simpler for permanent installations.
-
Do I need 3G-SDI for 1080p60?
Yes. 3G-SDI (SMPTE 424M) carries about 2.97 Gbit/s and is the format used for 1080p60.
-
Can an SDI encoder output 4K?
Some can, but many popular units stop at 1080p60. Check the output resolution and the SDI speed it accepts.
-
Do SDI IPTV encoders support multicast?
Many do, using UDP or RTP with IGMP. Check the spec sheet, because a long protocol list may still leave multicast out.
-
Is it legal to stream an SDI source over IP?
The equipment is legal. Whether you may stream a source depends on your license for that content, and you need that permission for each channel.
